10.3.1.8 Packet Tracer – Backing Up Configuration Files

10.3.1.8 Packet Tracer – Backing Up Configuration Files

From year to year, Cisco has updated many versions with difference questions. The latest version is version 6.0 in 2018. What is your version? It depends on your instructor creating your class. We recommend you to go thought all version if you are not clear. While you take online test with netacad.com, You may get random questions from all version. Each version have 1 to 10 different questions or more. After you review all questions, You should practice with our online test system by go to "Online Test" link below.

Version 5.02Version 5.03Version 6.0Online Assessment
Chapter 10 ExamChapter 10 ExamChapter 10 ExamOnline Test
Next Chapter
Practice FinalPractice FinalPractice FinalOnline Test
Lab Activities
10.1.1.4 Packet Tracer – Map a Network Using CDP
10.2.1.4 Packet Tracer – Configure and Verify NTP
10.2.3.5 Packet Tracer – Configuring Syslog and NTP
10.3.1.8 Packet Tracer – Backing Up Configuration Files
10.3.3.5 Packet Tracer – Using a TFTP Server to Upgrade a Cisco IOS Image
10.4.1.1 Packet Tracer – Skills Integration Challenge

Packet Tracer – Backing Up Configuration Files (Answer Version)

Answer Note: Red font color or Gray highlights indicate text that appears in the Answer copy only.

Topology

10.3.1.8 Packet Tracer – Backing Up Configuration Files

10.3.1.8 Packet Tracer – Backing Up Configuration Files

Objectives

Part 1: Establish Connectivity to TFTP Server

Part 2: Transfer Configuration from TFTP Server

Part 3: Backup Configuration and IOS to TFTP Server

Background / Scenario

This activity is designed to show how to restore a configuration from a backup and then perform a new backup. Due to an equipment failure, a new router has been put in place. Fortunately backup configuration files have been saved to a Trivial File Transfer Protocol (TFTP) Server. You are required to restore the files from the TFTP Server to get the router back online with as little down time as possible.

Part 1: Establish Connectivity to the TFTP Server

Note: Because this is a new router, initial configuration will be performed using a console connection to the router.

  1. Click PCA, then the Desktop tab, followed by Terminal to access the RTA command line.
  2. Configure and activate the Gigabit Ethernet 0/0 interface. The IP address should match the default gateway for the TFTP Server.
  3. Test connectivity to TFTP Server. Troubleshoot, if necessary.

Part 2: Transfer Configuration from the TFTP Server

  1. From privileged EXEC mode, issue the following command:
    • Router# copy tftp running-config
    • Address or name of remote host []? 172.16.1.2
    • Source filename []? RTA-confg
    • Destination filename [running-config]? <cr>
    • The router should return the following:
    • Accessing tftp://172.16.1.2/RTA-confg…
    • Loading RTA-confg from 172.16.1.2: !
    • [OK – 785 bytes]
    • 785 bytes copied in 0 secs
    • RTA#
    • %SYS-5-CONFIG_I: Configured from console by console
    • RTA#
  2. Issue the command to display the current configuration. What changes were made? The configuration stored on the TFTP Server was loaded into the router.
  3. Issue the appropriate show command to display the interface status. Are all interfaces active? No, Gi0/1 is administratively down. All router interfaces are shutdown by default.
  4. Correct any issues related to interface problems and test connectivity.

Part 3: Backup Configuration and IOS to TFTP Server

  1. Change the hostname of RTA to RTA-1.
  2. Save the configuration to NVRAM.
  3. Copy the configuration to the TFTP Server using the copy command:
    • RTA-1# copy running-config tftp:
    • Address or name of remote host []? 172.16.1.2
    • Destination filename [RTA-1-confg]? <cr>
  4. Issue the command to display the files in flash.
  5. Copy the IOS in flash to the TFTP Server using the following command:
    • RTA-1# copy flash tftp:
    • Source filename []? c1900-universalk9-mz.SPA.151-4.M4.bin
    • Address or name of remote host []? 172.16.1.2
    • Destination filename [c1900-universalk9-mz.SPA.151-4.M4.bin]? <cr>

From year to year, Cisco has updated many versions with difference questions. The latest version is version 6.0 in 2018. What is your version? It depends on your instructor creating your class. We recommend you to go thought all version if you are not clear. While you take online test with netacad.com, You may get random questions from all version. Each version have 1 to 10 different questions or more. After you review all questions, You should practice with our online test system by go to "Online Test" link below.

Version 5.02Version 5.03Version 6.0Online Assessment
Chapter 10 ExamChapter 10 ExamChapter 10 ExamOnline Test
Next Chapter
Practice FinalPractice FinalPractice FinalOnline Test
Lab Activities
10.1.1.4 Packet Tracer – Map a Network Using CDP
10.2.1.4 Packet Tracer – Configure and Verify NTP
10.2.3.5 Packet Tracer – Configuring Syslog and NTP
10.3.1.8 Packet Tracer – Backing Up Configuration Files
10.3.3.5 Packet Tracer – Using a TFTP Server to Upgrade a Cisco IOS Image
10.4.1.1 Packet Tracer – Skills Integration Challenge

Comments

comments