What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.)

What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.) speed and duplex settings MAC addresses next-hop addresses interface descriptions IP addresses Layer 1 statuses Explanation: The command show ip interface brief shows the IP address of each interface, as well as the operational status of the interfaces at both […]
Continue reading…

 

Refer to the exhibit. When a packet arrives on interface Serial0/0/0 on R1, with a destination IP address of PC1, which two events occur? (Choose two)

Refer to the exhibit. When a packet arrives on interface Serial0/0/0 on R1, with a destination IP address of PC1, which two events occur? (Choose two) Router R1 will forward the packet out Gig0/0. Router R1 will forward the packet out Gig0/1. Router R1 will forward the packet out S0/0/0. Router R1 will de-encapsulate the […]
Continue reading…

 

Refer to the exhibit. How was the host route 2001:DB8:CAFE:4::1/128 installed in the routing table?

Refer to the exhibit. How was the host route 2001:DB8:CAFE:4::1/128 installed in the routing table? The route was automatically installed when an IP address was configured on an active interface. The route was dynamically learned from another router. The route was manually entered by an administrator. The route was dynamically created by router R1. Answers […]
Continue reading…

 

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked? Check the configuration of the exit interface on the new static route. Verify that the static route to the server is present […]
Continue reading…

 

Refer to the exhibit. The routing table for R2 is as follows: What will router R2 do with a packet destined for 192.168.10.129?

Refer to the exhibit. The routing table for R2 is as follows: Gateway of last resort is not set 10.0.0.0/30 is subnetted, 2 subnets C 10.0.0.0 is directly connected, Serial0/0/0 C 10.0.0.4 is directly connected, Serial0/0/1 192.168.10.0/26 is subnetted, 3 subnets S 192.168.10.0 is directly connected, Serial0/0/0 C 192.168.10.64 is directly connected, FastEthernet0/0 S 192.168.10.128 […]
Continue reading…

 

What does the 5 at the end of the command signify?

Consider the following command: ip route 192.168.10.0 255.255.255.0 10.10.10.2 5 What does the 5 at the end of the command signify? metric exit interface administrative distance maximum number of hops to the 192.168.10.0/24 network Answers Explanation & Hints: The 5 at the end of the command signifies administrative distance. This value is added to floating […]
Continue reading…

 

Which command would create a valid IPv6 default route?

Which command would create a valid IPv6 default route? ipv6 route ::/0 fe80::1 ipv6 route 2001:db8:acad:1::/64 ::1 ipv6 route ::/0 2001:db8:acad:2::a ipv6 route ::/128 2001:db8:acad:1::1 Answers Explanation & Hints: The correct prefix and prefix length for a default route is ::/0, which matches any address. ::/128 matches only the specific address of all zeros. When […]
Continue reading…

 

Refer to the exhibit. Router R1 has an OSPF neighbor relationship with the ISP router over the 192.168.0.32 network. The 192.168.0.36 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/0/1 100 was issued on R1 and now traffic is using the backup link even when the OSPF link is up and functioning. Which change should be made to the static route command so that traffic will only use the OSPF link when it is up?​

Refer to the exhibit. Router R1 has an OSPF neighbor relationship with the ISP router over the 192.168.0.32 network. The 192.168.0.36 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/0/1 100 was issued on R1 and now traffic is using the […]
Continue reading…

 

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.)

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) Answers Explanation & Hints: route source protocol = D (which is EIGRP) destination network = 10.3.0.0 metric = 21024000 administrative distance = 1 next hop = 172.16.2.2 route timestamp = 00:22:15   For more question and answers: Click […]
Continue reading…

 

What are two characteristics of Cisco Express Forwarding (CEF)? (Choose two.)

What are two characteristics of Cisco Express Forwarding (CEF)? (Choose two.) Packets are forwarded based on information in the FIB and an adjacency table. When a packet arrives on a router interface, it is forwarded to the control plane where the CPU matches the destination address with a matching routing table entry. When a packet […]
Continue reading…

 

Refer to the exhibit. Which interface will be the exit interface to forward a data packet that has the destination IP address 172.18.109.152?

Gateway of last resort is not set. 172.18.109.0/26 is variously subnetted, 7 subnets, 3 masks O 172.18.109.0/26 [110/10] via 172.18.32.1, 00:00:24, Serial0/0/0 O 172.18.109.64/26 [110/20] via 172.18.32.6, 00:00:56, Serial 0/0/1 O 172.18.109.128/26 [110/10] via 172.18.32.1, 00:00:24, Serial 0/0/0 C 172.18.109.192/27 is directly connected, GigabitEthernet0/0 L 172.18.109.193/27 is directly connected, GigabitEthernet0/0 C 172.18.109.224/27 is directly connected, […]
Continue reading…

 

What address and prefix length is used when configuring an IPv6 default static route?

What address and prefix length is used when configuring an IPv6 default static route? ::/0 ::1/128 0.0.0.0/0 FF02::1/8 Answers Explanation & Hints: The IPv6 address and prefix for a default static route is ::/0. This represents all zeros in the address and a prefix length of zero. For more question and answers: Click Here CCNA […]
Continue reading…

 

Match the dynamic routing protocol component to the characteristic. (Not all options are used.)

Match the dynamic routing protocol component to the characteristic. (Not all options are used.) Answers Explanation & Hints: The three components of dynamic routing protocols include: Data structures Routing protocol messages Algorithm For more question and answers: Click Here CCNA 2 SRWE v7 – SRWE Practice Final Exam Answers Full 100%
Continue reading…

 

A network administrator is configuring a WLC to provide WLAN access to users in an office building. When testing the newly created WLAN, the administrator does not see the SSID from a wireless device. What is a possible cause?

A network administrator is configuring a WLC to provide WLAN access to users in an office building. When testing the newly created WLAN, the administrator does not see the SSID from a wireless device. What is a possible cause? The new WLAN needs to be enabled. The RADUIS server is not operational. The WLAN security […]
Continue reading…