Refer to the exhibit. A network engineer has been given the network address of 192.168.99.0 and a subnet mask of 255.255.255.192 to subnet across the four networks shown. How many total host addresses are unused across all four subnets?

Last Updated on April 13, 2020 by AdminRefer to the exhibit. A network engineer has been given the network address of 192.168.99.0 and a subnet mask of 255.255.255.192 to subnet across the four networks shown. How many total host addresses are unused across all four subnets? 158 200 224 88 72 Explanation: The network IP […]
Continue reading…

 

Refer to the exhibit. The network administrator has assigned the LAN of LBMISS an address range of 192.168.10.0. This address range has been subnetted using a /29 prefix. In order to accommodate a new building, the technician has decided to use the fifth subnet for configuring the new network (subnet zero is the first subnet). By company policies, the router interface is always assigned the first usable host address and the workgroup server is given the last usable host address. Which configuration should be entered into the properties of the workgroup server to allow connectivity to the Internet?

Last Updated on April 13, 2020 by AdminRefer to the exhibit. The network administrator has assigned the LAN of LBMISS an address range of 192.168.10.0. This address range has been subnetted using a /29 prefix. In order to accommodate a new building, the technician has decided to use the fifth subnet for configuring the new […]
Continue reading…

 

The network administrator has deemed that 192.168.10.0/24 is to be the network used at this site. Which single subnet mask would make the most efficient use of the available addresses to use for the four subnetworks?

Last Updated on April 13, 2020 by AdminA network administrator wants to have the same network mask for all networks at a particular small site. The site has the following networks and number of devices:IP phones – 22 addresses PCs – 20 addresses needed Printers – 2 addresses needed Scanners – 2 addresses needed The […]
Continue reading…

 

Match each item to the type of topology diagram on which it is typically identified. (Not all options are used.)

Last Updated on April 13, 2020 by AdminMatch each item to the type of topology diagram on which it is typically identified. (Not all options are used.) Explanation: A logical topology diagram typically depicts the IP addressing scheme and groupings of devices and ports. A physical topology diagram shows how those devices are connected to […]
Continue reading…

 

Which subnet would include the address 192.168.1.96 as a usable host address?

Last Updated on April 13, 2020 by AdminWhich subnet would include the address 192.168.1.96 as a usable host address? 192.168.1.32/27 192.168.1.32/28 192.168.1.64/29 192.168.1.64/26 Explanation: For the subnet of 192.168.1.64/26, there are 6 bits for host addresses, yielding 64 possible addresses. However, the first and last subnets are the network and broadcast addresses for this subnet. […]
Continue reading…

 

Refer to the exhibit. On the basis of the output, which two statements about network connectivity are correct? (Choose two.)

Last Updated on April 13, 2020 by AdminRefer to the exhibit. On the basis of the output, which two statements about network connectivity are correct? (Choose two.) This host does not have a default gateway configured. There are 4 hops between this device and the device at 192.168.100.1. The average transmission time between the two […]
Continue reading…

 

Refer to the exhibit. An administrator is trying to configure the switch but receives the error message that is displayed in the exhibit. What is the problem?

Last Updated on April 13, 2020 by AdminRefer to the exhibit. An administrator is trying to configure the switch but receives the error message that is displayed in the exhibit. What is the problem? The entire command, configure terminal , must be used. The administrator must connect via the console port to access global configuration mode. The […]
Continue reading…

 

Which range of link-local addresses can be assigned to an IPv6-enabled interface?​

Last Updated on April 13, 2020 by AdminWhich range of link-local addresses can be assigned to an IPv6-enabled interface?​ FE80::/10 FDEE::/7​ FF00::/8​ FEC0::/10​ Explanation: Link-local addresses are in the range of FE80::/10 to FEBF::/10. The original IPv6 specification defined site-local addresses and used the prefix range FEC0::/10, but these addresses were deprecated by the IETF […]
Continue reading…

 

What happens when the transport input ssh command is entered on the switch vty lines?

Last Updated on April 13, 2020 by AdminWhat happens when the transport input ssh command is entered on the switch vty lines? The switch requires a username/password combination for remote access. The SSH client on the switch is enabled. Communication between the switch and remote users is encrypted. The switch requires remote connections via a proprietary client […]
Continue reading…