CCNA2 v6.0 Chapter 3 Exam Answers 2019

CCNA2 v6.0 Chapter 3 Exam Answers 2018 2019

From year to year, Cisco has updated many versions with difference questions. The latest version is version 6.0 in 2018. What is your version? It depends on your instructor creating your class. We recommend you to go thought all version if you are not clear. While you take online test with netacad.com, You may get random questions from all version. Each version have 1 to 10 different questions or more. After you review all questions, You should practice with our online test system by go to "Online Test" link below.

Version 5.02Version 5.03Version 6.0Online Assessment
Chapter 3 ExamChapter 3 ExamChapter 3 ExamOnline Test 
Next Chapter
Chapter 4 ExamChapter 4 ExamChapter 4 ExamOnline Test 
Lab Activities 
3.2.1.8 Packet Tracer – Configuring RIPv2
  1. Which dynamic routing protocol was developed to interconnect different Internet service providers?

    • BGP
    • EIGRP
    • OSPF
    • RIP
  2. Which routing protocol is limited to smaller network implementations because it does not accommodate growth for larger networks?

    • OSPF
    • RIP
    • EIGRP
    • IS-IS
  3. What two tasks do dynamic routing protocols perform? (Choose two.)

    • discover hosts
    • update and maintain routing tables
    • propagate host default gateways
    • network discovery
    • assign IP addressing
  4. When would it be more beneficial to use a dynamic routing protocol instead of static routing?

    • in an organization with a smaller network that is not expected to grow in size
    • on a stub network that has a single exit point
    • in an organization where routers suffer from performance issues
    • on a network where there is a lot of topology changes
  5. When would it be more beneficial to use static routing instead of dynamic routing protocols?

    • on a network where dynamic updates would pose a security risk
    • on a network that is expected to continually grow in size
    • on a network that has a large amount of redundant paths
    • on a network that commonly experiences link failures
  6. What is a purpose of the network command when configuring RIPv2 as the routing protocol?

    • It identifies the interfaces that belong to a specified network.
    • It specifies the remote network that can now be reached.
    • It immediately advertises the specified network to neighbor routers with a classful mask.
    • It populates the routing table with the network entry.
  7. A network administrator configures a static route on the edge router of a network to assign a gateway of last resort. How would a network administrator configure the edge router to automatically share this route within RIP?

    • Use the auto-summary command.
    • Use the passive-interface command.
    • Use the network command.
    • Use the default-information originate command.
  8. What is the purpose of the passive-interface command?

    • allows a routing protocol to forward updates out an interface that is missing its IP address
    • allows a router to send routing updates on an interface but not receive updates via that interface
    • allows an interface to remain up without receiving keepalives
    • allows interfaces to share IP addresses
    • allows a router to receive routing updates on an interface but not send updates via that interface
  9. Which route would be automatically created when a router interface is activated and configured with an IP address?

    • D 10.16.0.0/24 [90/3256] via 192.168.6.9
    • C 192.168.0.0/24 is directly connected, FastEthernet 0/0
    • S 192.168.1.0/24 is directly connected, FastEthernet 0/1
    • O 172.16.0.0/16 [110/65] via 192.168.5.1
  10. Refer to the exhibit. Which two types of routes could be used to describe the 192.168.200.0/30 route? (Choose two.)

    CCNA2 v6.0 Chapter 3 Exam 002

    CCNA2 v6.0 Chapter 3 Exam 002

    • ultimate route
    • level 1 parent route
    • level 1 network route
    • level 2 child route
    • supernet route
  11. What occurs next in the router lookup process after a router identifies a destination IP address and locates a matching level 1 parent route?

    • The level 2 child routes are examined.
    • The level 1 supernet routes are examined.
    • The level 1 ultimate routes are examined.
    • The router drops the packet.
  12. Which route would be used to forward a packet with a source IP address of 192.168.10.1 and a destination IP address of 10.1.1.1?

    • C 192.168.10.0/30 is directly connected, GigabitEthernet0/1
    • S 10.1.0.0/16 is directly connected, GigabitEthernet0/0
    • O 10.1.1.0/24 [110/65] via 192.168.200.2, 00:01:20, Serial0/1/0
    • S* 0.0.0.0/0 [1/0] via 172.16.1.1
  13. Which two requirements are used to determine if a route can be considered as an ultimate route in a router’s routing table? (Choose two.)

    • contain subnets
    • be a default route
    • contain an exit interface
    • be a classful network entry
    • contain a next-hop IP address
  14. What is a disadvantage of using dynamic routing protocols?

    • They are only suitable for simple topologies.
    • Their configuration complexity increases as the size of the network grows.
    • They send messages about network status insecurely across networks by default.
    • They require administrator intervention when the pathway of traffic changes.
  15. Which two statements are true regarding classless routing protocols? (Choose two.)

    • sends subnet mask information in routing updates
    • sends complete routing table update to all neighbors
    • is supported by RIP version 1
    • allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
    • reduces the amount of address space available in an organization
  16. Refer to the exhibit. Based on the partial output from the show ip route command, what two facts can be determined about the RIP routing protocol? (Choose two.)

    CCNA2 v6.0 Chapter 3 Exam 003

    CCNA2 v6.0 Chapter 3 Exam 003

    • RIP version 2 is running on this router and its RIP neighbor.
    • The metric to the network 172.16.0.0 is 120.
    • RIP version 1 is running on this router and its RIP neighbor.
    • The command no auto-summary has been used on the RIP neighbor router.
    • RIP will advertise two networks to its neighbor.
  17. While configuring RIPv2 on an enterprise network, an engineer enters the command network 192.168.10.0 into router configuration mode.

    What is the result of entering this command?

    • The interface of the 192.168.10.0 network is sending version 1 and version 2 updates.
    • The interface of the 192.168.10.0 network is receiving version 1 and version 2 updates.
    • The interface of the 192.168.10.0 network is sending only version 2 updates.
    • The interface of the 192.168.10.0 network is sending RIP hello messages.
  18. A destination route in the routing table is indicated with a code D. Which kind of route entry is this?

    • a static route
    • a route used as the default gateway
    • a network directly connected to a router interface
    • a route dynamically learned through the EIGRP routing protocol
  19. Refer to the exhibit. Which interface will be the exit interface to forward a data packet with the destination IP address 172.16.0.66?

    CCNA2 v6.0 Chapter 3 Exam 001

    CCNA2 v6.0 Chapter 3 Exam 001

    • Serial0/0/0
    • Serial0/0/1
    • GigabitEthernet0/0
    • GigabitEthernet0/1
  20. Which type of route will require a router to perform a recursive lookup?

    • an ultimate route that is using a next hop IP address on a router that is not using CEF
    • a level 2 child route that is using an exit interface on a router that is not using CEF
    • a level 1 network route that is using a next hop IP address on a router that is using CEF
    • a parent route on a router that is using CEF
  21. Which route is the best match for a packet entering a router with a destination address of 10.16.0.2?

    • S 10.0.0.0/8 [1/0] via 192.168.0.2
    • S 10.16.0.0/24 [1/0] via 192.168.0.9
    • S 10.16.0.0/16 is directly connected, Ethernet 0/1
    • S 10.0.0.0/16 is directly connected, Ethernet 0/0

From year to year, Cisco has updated many versions with difference questions. The latest version is version 6.0 in 2018. What is your version? It depends on your instructor creating your class. We recommend you to go thought all version if you are not clear. While you take online test with netacad.com, You may get random questions from all version. Each version have 1 to 10 different questions or more. After you review all questions, You should practice with our online test system by go to "Online Test" link below.

Version 5.02Version 5.03Version 6.0Online Assessment
Chapter 3 ExamChapter 3 ExamChapter 3 ExamOnline Test 
Next Chapter
Chapter 4 ExamChapter 4 ExamChapter 4 ExamOnline Test 
Lab Activities 
3.2.1.8 Packet Tracer – Configuring RIPv2

Comments

comments