CCNA3 v6.0 Chapter 3 Exam Full 100%

CCNA3 v6.0 Chapter 3 Exam Full 100%

  1. 1. Question

    Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

  2. 2. Question

    What is the outcome of a Layer 2 broadcast storm?

  3. 3. Question
    What is the purpose of the Spanning Tree Protocol (STP)?
  4. 4. Question
    What is a characteristic of a Layer 2 loop?
  5. 5. Question
    What additional information is contained in the 12-bit extended system ID of a BPDU?
  6. 6. Question
    Which three components are combined to form a bridge ID?
  7. 7. Question

    Refer to the exhibit. Which switch will be elected the root bridge and which switch will place a port in blocking mode? (Choose two.)

    CCNA3 v6.0 Chapter 3 Exam 03

    CCNA3 v6.0 Chapter 3 Exam 03

  8. 8. Question

    Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?

    CCNA3 v6.0 Chapter 3 Exam 01

    CCNA3 v6.0 Chapter 3 Exam 01

  9. 9. Question
    Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?
  10. 10. Question
    Which Cisco switch feature ensures that configured switch edge ports do not cause Layer 2 loops if a port is mistakenly connected to another switch?
  11. 11. Question
    Which two types of spanning tree protocols can cause suboptimal traffic flows because they assume only one spanning-tree instance for the entire bridged network? (Choose two.)
  12. 12. Question
    Which spanning tree standard supports only one root bridge so that traffic from all VLANs flows over the same path?
  13. 13. Question
    What is an advantage of PVST+?
  14. 14. Question
    In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)
  15. 15. Question
    If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?
  16. 16. Question
    Which RSTP ports are connected to end devices?
  17. 17. Question
    A network administrator is preparing the implementation of Rapid PVST+ on a production network. How are the Rapid PVST+ link types determined on the switch interfaces?
  18. 18. Question
    Which port state will switch ports immediately transition to when configured for PortFast?
  19. 19. Question
    Which STP priority configuration would ensure that a switch would always be the root switch?
  20. 20. Question

    Refer to the exhibit. What is the role of the SW3 switch?

    CCNA3 v6.0 Chapter 3 Exam 02

    CCNA3 v6.0 Chapter 3 Exam 02

  21. 21. Question

    To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)

  22. 22. Question
    What port type is used to interconnect switches in a switch stack?
  23. 23. Question

    Match the spanning-tree feature with the protocol type. (Not all options are used.)

    • CCNA2 v6.0 Chapter 3 Exam 01

      CCNA2 v6.0 Chapter 3 Exam 01

  24. 24. Question

    Fill in the blank. Do not use abbreviations.
    The spanning-tree       mode rapid-pvst         global configuration command is used to enable Rapid PVST+.

  25. 25. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
    Which switch is the root bridge?​

Comments

comments