CCNA3 v6.0 Chapter 8 Exam Full 100%

CCNA3 v6.0 Chapter 8 Exam Full 100%

From year to year, Cisco has updated many versions with difference questions. The latest version is version 6.0 in 2018. What is your version? It depends on your instructor creating your class. We recommend you to go thought all version if you are not clear. While you take online test with netacad.com, You may get random questions from all version. Each version have 1 to 10 different questions or more. After you review all questions, You should practice with our online test system by go to "Online Test" link below.

Version 5.02 Version 5.03 Version 6.0 Online Assessment
Chapter 8 Exam Chapter 8 Exam Chapter 8 Exam Online Test
Next Chapter
Chapter 9 Exam Chapter 9 Exam Chapter 9 Exam Online Test
Lab Activities
8.2.2.7 Packet Tracer – Configuring OSPFv2 in a Single Area
8.3.3.5 Packet Tracer – Configuring Basic OSPFv3 in a Single Area
8.4.1.2 Packet Tracer – Skills Integration Challenge
  1. 1. Question

    What is used to create the OSPF neighbor table?

  2. 2. Question
    Which OSPF component is identical in all routers in an OSPF area after convergence?
  3. 3. Question

    Which OPSF packet contains the different types of link-state advertisements?

  4. 4. Question
    What happens immediately after two OSPF routers have exchanged hello packets and have formed a neighbor adjacency?
  5. 5. Question
    What will an OSPF router prefer to use first as a router ID?
  6. 6. Question
    What are the two purposes of an OSPF router ID? (Choose two.)
  7. 7. Question
    By default, what is the OSPF cost for any link with a bandwidth of 100 Mb/s or greater?
  8. 8. Question
    Which command should be used to check the OSPF process ID, the router ID, networks the router is advertising, the neighbors the router is receiving updates from, and the default administrative distance?
  9. 9. Question
    What are two reasons that will prevent two routers from forming an OSPFv2 adjacency? (Choose two.)
  10. 10. Question
    Which three addresses could be used as the destination address for OSPFv3 messages? (Choose three.)
  11. 11. Question
    A network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command?
  12. 12. Question
    When a network engineer is configuring OSPFv3 on a router, which command would the engineer issue immediately before configuring the router ID?
  13. 13. Question
    Single area OSPFv3 has been enabled on a router via the ipv6 router ospf 20 command. Which command will enable this OSPFv3 process on an interface of that router?
  14. 14. Question
    What does a Cisco router use automatically to create link-local addresses on serial interfaces when OSPFv3 is implemented?
  15. 15. Question
    Which command will verify that a router that is running OSPFv3 has formed an adjacency with other routers in its OSPF area?
  16. 16. Question
    Which command will provide information specific to OSPFv3 routes in the routing table?
  17. 17. Question

    Match the OSPF state with the order in which it occurs. (Not all options are used.)

    CCNA3 v6.0 Chapter 8 Exam 01

    CCNA3 v6.0 Chapter 8 Exam 01

  18. 18. Question

    Match each OSPF packet type to how it is used by a router. (Not all options are used.)

    CCNA3 v6.0 Chapter 8 Exam 02

    CCNA3 v6.0 Chapter 8 Exam 02

  19. 19. Question

    By order of precedence, match the selection of router ID for an OSPF-enable router to the possible router ID options. (Not all option are used.)

    CCNA3 v6.0 Chapter 8 Exam 03

    CCNA3 v6.0 Chapter 8 Exam 03

  20. 20. Question

    Match the information to the command that is used to obtain the information. (Not all options are used.)

    CCNA3 v6.0 Chapter 8 Exam 04

    CCNA3 v6.0 Chapter 8 Exam 04

  21. 21. Question

    Fill in the blank.
    OSPF uses     cost         as a metric.

  22. 22. Question

    Fill in the blank.
    The election of a DR and a BDR takes place on         multiaccess         networks, such as Ethernet networks.

  23. 23. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then complete the task.

    What message is displayed on http://www.ciscoville.com?

From year to year, Cisco has updated many versions with difference questions. The latest version is version 6.0 in 2018. What is your version? It depends on your instructor creating your class. We recommend you to go thought all version if you are not clear. While you take online test with netacad.com, You may get random questions from all version. Each version have 1 to 10 different questions or more. After you review all questions, You should practice with our online test system by go to "Online Test" link below.

Version 5.02 Version 5.03 Version 6.0 Online Assessment
Chapter 8 Exam Chapter 8 Exam Chapter 8 Exam Online Test
Next Chapter
Chapter 9 Exam Chapter 9 Exam Chapter 9 Exam Online Test
Lab Activities
8.2.2.7 Packet Tracer – Configuring OSPFv2 in a Single Area
8.3.3.5 Packet Tracer – Configuring Basic OSPFv3 in a Single Area
8.4.1.2 Packet Tracer – Skills Integration Challenge

Comments

comments