CCNA3 v6.0 Practice Final Full 100%

CCNA3 v6.0 Practice Final Full 100%

  1. 1. Question
    Which action should be taken when planning for redundancy on a hierarchical network design?
  2. 2. Question
    What is the function of STP in a scalable network?
  3. 3. Question

    As the network administrator you have been asked to implement EtherChannel on the corporate network. What does this configuration consist of?

  4. 4. Question
    How does implementing STP allow for a scalable network design?
  5. 5. Question
    Which model and which two characteristics would be more likely to be considered in purchasing an access layer switch, as compared to buying switches that operate at the other layers of the Cisco hierarchical design model? (Choose three.)
  6. 6. Question
    What is the function of ASICs in a multilayer switch?
  7. 7. Question
    In a large enterprise network, which two functions are performed by routers at the distribution layer? (Choose two.)
  8. 8. Question
    Which two VTP modes allow for the creation, modification, and deletion of VLANs on the local switch? (Choose two.)
  9. 9. Question
    Which three steps should be taken before moving a Cisco switch to a new VTP management domain? (Choose three.)
  10. 10. Question
    The network administrator wants to configure a switch to pass VLAN update information to other switches in the domain but not update its own local VLAN database. Which two steps should the administrator perform to achieve this? (Choose two.)
  11. 11. Question

    Refer to the exhibit. The partial configuration that is shown was used to configure router on a stick for VLANS 10, 30, and 50. However, testing shows that there are some connectivity problems between the VLANs. Which configuration error is causing this problem?

    CCNA3 v6.0 Practice Final 019

    CCNA3 v6.0 Practice Final 019

  12. 12. Question
    Which two statements are characteristics of routed ports on a multilayer switch? (Choose two.)​
  13. 13. Question

    Refer to the exhibit. A Layer 3 switch routes for three VLANs and connects to a router for Internet connectivity. Which two configurations would be applied to the switch? (Choose two.)

    CCNA3 v6.0 Practice Final 020

    CCNA3 v6.0 Practice Final 020

  14. 14. Question

    Refer to the exhibit. Which switch will be the root bridge after the election process is complete?

    CCNA3 v6.0 Practice Final 010

    CCNA3 v6.0 Practice Final 010

  15. 15. Question
    What two STP features are incorporated into Rapid PVST+? (Choose two.)
  16. 16. Question

    Refer to the exhibit. A network administrator is configuring PVST+ for the three switches. What will be a result of entering these commands?

    CCNA3 v6.0 Practice Final 009

    CCNA3 v6.0 Practice Final 009

  17. 17. Question

    Refer to the exhibit. If the switch has been configured for PVST+ mode, what command output would replace the question marks?

    CCNA3 v6.0 Practice Final 008

    CCNA3 v6.0 Practice Final 008

  18. 18. Question
    Which function is provided by EtherChannel?
  19. 19. Question
    Which technology is an open protocol standard that allows switches to automatically bundle physical ports into a single logical link?
  20. 20. Question

    Refer to the exhibit. A network administrator has connected two switches together using EtherChannel technology. If STP is running, what will be the end result?

    CCNA3 v6.0 Practice Final 004

    CCNA3 v6.0 Practice Final 004

  21. 21. Question
    What are two requirements to be able to configure an EtherChannel between two switches? (Choose two.)
  22. 22. Question

    Refer to the exhibit. Based on the command output shown, what is the status of the EtherChannel?

    CCNA3 v6.0 Practice Final 003

    CCNA3 v6.0 Practice Final 003

  23. 23. Question
    A network engineer is configuring a LAN with a redundant first hop to make better use of the available network resources. Which protocol should the engineer implement?
  24. 24. Question
    Which dynamic routing protocol uses hop count to calculate metric value?
  25. 25. Question
    Which two commands are used in the implementation of a dynamic IPv4 routing protocol? (Choose two.)
  26. 26. Question
    Which statement describes the Autonomous System number that is used in EIGRP?
  27. 27. Question
    What are two reasons to implement passive interfaces in the EIGRP configuration of a Cisco router? (Choose two.)
  28. 28. Question

    Refer to the exhibit. A network administrator issues the show ip protocols command. Based on the exhibited output, what can be concluded?

    CCNA3 v6.0 Practice Final 013

    CCNA3 v6.0 Practice Final 013

  29. 29. Question

    Refer to the exhibit. A network administrator has issued the show ip eigrp neighbors command. What can be concluded from the output?

    CCNA3 v6.0 Practice Final 014

    CCNA3 v6.0 Practice Final 014

  30. 30. Question
    Which two metric weights are set to one by default when costs in EIGRP are being calculated? (Choose two.)
  31. 31. Question
    Which feature of the EIGRP routing protocol can provide fast re-convergence without DUAL recomputation in the event of a route failure?
  32. 32. Question

    Refer to the exhibit. An administrator attempts to configure EIGRP for IPv6 on a router and receives the error message that is shown. Which command must be issued by the administrator before EIGRP for IPv6 can be configured?

    CCNA3 v6.0 Practice Final 001

    CCNA3 v6.0 Practice Final 001

  33. 33. Question

    Refer to the exhibit. What will Router1 do if it receives packets that are destined to network 172.16.4.0/24?

    CCNA3 v6.0 Practice Final 006

    CCNA3 v6.0 Practice Final 006

  34. 34. Question
    In which IOS CLI mode must a network administrator issue the maximum-paths command to configure load balancing in EIGRP?​
  35. 35. Question

    Refer to the exhibit. Which command will configure unequal-cost load balancing with EIGRP on the HQ router?

    CCNA3 v6.0 Practice Final 011

    CCNA3 v6.0 Practice Final 011

  36. 36. Question

    Refer to the exhibit. Why did R1 and R2 not establish an adjacency?

    CCNA3 v6.0 Practice Final 018

    CCNA3 v6.0 Practice Final 018

  37. 37. Question
    For troubleshooting missing EIGRP routes on a router, what three types of information can be collected using the show ip protocols command? (Choose three.)
  38. 38. Question

    Refer to the exhibit. The routing table on R2 does not include all networks that are attached to R1. The network administrator verifies that the network statement is configured to include these two networks. What is a possible cause of the issue?

    CCNA3 v6.0 Practice Final 012

    CCNA3 v6.0 Practice Final 012

  39. 39. Question
    A network administrator is troubleshooting the EIGRP routing between two routers, R1 and R2. The problem is found to be that only some, but not all networks attached to R1 are listed in the routing table of router R2. What should the administrator investigate on router R1 to determine the cause of the problem?
  40. 40. Question
    What is the order of packet types used by an OSPF router to establish convergence?
  41. 41. Question
    Which wildcard mask would be used to advertise the 192.168.5.96/27 network as part of an OSPF configuration?
  42. 42. Question
    What is the reason for a network engineer to alter the default reference bandwidth parameter when configuring OSPF?
  43. 43. Question
    Which OSPFv3 function works differently from OSPFv2?
  44. 44. Question

    Refer to the exhibit. Which address will R1 use as the source address for all OSPFv3 messages that will be sent to neighbors?

    CCNA3 v6.0 Practice Final 015

    CCNA3 v6.0 Practice Final 015

  45. 45. Question
    What address type will OSPFv3 use to form adjacencies to neighboring routers?
  46. 46. Question
    On what type of OSPF router is interarea route summarization configured?
  47. 47. Question
    Which type of OSPF LSA represents an external route and is propagated across the entire OSPF domain?
  48. 48. Question
    Which OSPF LSA type is only used in multiaccess and NBMA networks?
  49. 49. Question

    Refer to the exhibit. What can be concluded about network 192.168.1.0 in the R2 routing table?

    CCNA3 v6.0 Practice Final 017

    CCNA3 v6.0 Practice Final 017

  50. 50. Question

    Refer to the exhibit. What are three results for the DR and BDR elections for the given topologies? (Choose three.)

    CCNA3 v6.0 Practice Final 016

    CCNA3 v6.0 Practice Final 016

  51. 51. Question
    What is one reason to use the ip ospf priority command when the OSPF routing protocol is in use?
  52. 52. Question

    Refer to the exhibit. Suppose that routers B, C, and D have a default priority, and router A has a priority 0. Which conclusion can be drawn from the DR/BDR election process?​

    CCNA3 v6.0 Practice Final 007

    CCNA3 v6.0 Practice Final 007

  53. 53. Question

    Refer to the exhibit. On which router or routers would a default route be statically configured in a corporate environment that uses single area OSPF as the routing protocol?

    CCNA3 v6.0 Practice Final 005

    CCNA3 v6.0 Practice Final 005

  54. 54. Question

    Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers as shown. The routers are unable to form a neighbor adjacency. What should be done to fix the problem?

    CCNA3 v6.0 Practice Final 002

    CCNA3 v6.0 Practice Final 002

  55. 55. Question
    An administrator is troubleshooting an adjacency issue between two OSPFv3 routers. Which two neighbor states indicate a stable adjacency between the routers? (Choose two.)
  56. 56. Question

    Fill in the blank.
    In RSTP, BPDU frames are sent every        2               seconds by default.

  57. 57. Question

    Fill in the blank.
    What is the acronym of an IGP, link-state, classless routing protocol besides IS-IS?      OSPF  

  58. 58. Question

    Fill in the blank.
    EIGRP keeps feasible successor routes in the       topology        table.

  59. 59. Question

    Fill in the blank.
    By default, EIGRP is able to use up to           50               percent of the bandwidth for EIGRP messages on an EIGRP-enabled interface.

  60. 60. Question

    Match the switched LAN problem to the correct symptom. (Not all options are used.)

    CCNA3 v6.0 Practice Final 01

    CCNA3 v6.0 Practice Final 01

  61. 61. Question

    Match the port state with its condition. (Not all options are used.)

    CCNA3 v6.0 Practice Final 02

    CCNA3 v6.0 Practice Final 02

  62. 62. Question

    Match the step sequence to the multiarea OSPF route calculation process. (Not all options are used.)

    CCNA3 v6.0 Practice Final 03

    CCNA3 v6.0 Practice Final 03

  63. 63. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

    Which message was displayed on the web server?

Comments

comments